Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not undervalue the forklift at work. If the operation is not good, there will be major mishaps in mins, and there are lots of crashes entailing forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which almost causes an crash.
Instance 4: Forklift is speeding up and rolls over during a turn.
Instance 5: The forklift vehicle driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn first and then start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a load, the vehicle driver ought to initially verify that the lots is steady and dependable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be provided initially. High-speed doglegs are banned. High-speed doglegs will create the vehicle to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and should keep a specific safety and security range from the vehicle in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The tons shall not be raised except when stacking or loading. .
8. The height of the tons should not block the chauffeur's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a prompt way, and they will never ever operate with diseases or hide them.

packing and unloading.
1. When fork-loading things, the range between both forks must be adjusted as required to make the tons of both forks well balanced and not skewed, and one side of the thing ought to be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special scenarios, security indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure individuals. .
5. Stand-on Electric Pallet Stacker When using a fork to fork the goods, the fork needs to be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other goods or items. The lots should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It Electric Forklift Truck for Warehouse is prohibited to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you come across somebody in front of you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Adding and down the slope should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to pick up the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the exact same length as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844